Euro Tile Sand is a unique mixture of polymer binders and calibrated sand available in Beige, Slate Grey, Ivory and Black Diamond. Once Euro Tile Sand sets, it becomes very firm and locks between the tile joints while still retaining flexibility and providing a long lasting, durable jointing material. Euro Tile Sand is recommended for a variety of pedestrian uses including pool decks, patios, footpaths etc.
Step 1 • Excavation of the new Euro Tile area
Excavate the new Euro Base area. The depth required is calculated by adding Porcelain Tile height, Euro Base, bedding sand, plus any soft organic material that has to be removed. Excavate the perimeter an extra 6" (15 cm) wider on all sides than the tile area required.
Step 2 • Levelling and compacting of the base
(A) Ensure a slope of at least 1 degree away from any structure, such as a house.
(B) • The native soil needs to be compacted using a plate compactor or hand tamper.
Step 3 • Addition of Gator Fabric GF 4.4, Levelling and compacted bedding sand
(A) • Lay down a non-woven Gator Fabric GF 4.4 geotextile (minimum 100 LBF) and cover the entire excavated area.
(B) • Spread an even layer of sand, no more than 3/4” thick (19 mm) • Levelling and compacting the bedding sand will be the last step prior to installing the Euro Base.
(C) • Water the sand prior to using a hand compactor and/or plate compactor, compacting the 3/4” (19 mm) layer of bedding sand until you obtain a final height of 1/2” (13 mm) of compacted bedding sand. This compacted surface should reflect the final tiled surface.
Step 4 • Installation of the Euro Base
Make sure to install the Euro Base on the extended excavation area (total excavation should be 6 inches [15 cm] wider on each side than the final tiled area).
• Start laying the Euro Base units ensuring Euro Base interlocks with the tongue & groove system.
Step 5 • Installation of Porcelain tile and Euro Spacer
Euro Spacers should receive a generous amount of Euro XP glue on each quadrant. Install the Porcelain Tile on the Euro Spacer, apply pressure or tap the tiles with a rubber mallet at all corners. This will ensure that the tiles are adhering to the Euro Spacer. The Euro Spacer will be left in the tile installation permanently, ensuring proper alignment and stability of your project for years to come.
Step 6 • Installation of Euro Tile Edge and Euro Screws
Install Euro Tile Edge on the Euro Base using Euro Base Screws, make sure that Euro Tile Edge rests firmly against the tiles. Use Euro Base Screws at every second hole.
Step 7 • Sweeping, compacting and blowing of the Euro tile Sand
(A) • When emptying the bag of EURO TILE SAND, spread it onto the dry, tiled surface.• When sweeping the EURO TILE SAND, spread it over a small area before moving onto the next, while making sure to fill in the joints.
(B) • It is now time to compact the sand into the joints using a roller compactor or rubber mallet. Do not use a plate compactor. Repeat filling and compacting of the tile joints. Finally, sweep the surface with a fine bristle broom and remove all excess sand. • Ensure the sand is 1/8 inch (3 mm) lower than the tile chamfers
(C) • Finally, use a blower to blow off all sand residue laying on the tile surface.
Step 8 • Euro Tile Sand water activation steps
(A) • Shower water on a specific area of 100 sq.ft., wait no longer than 2 to 3 minutes.
(B) • Shower and rinse simultaneously on a section of approximately 100 sq. ft. so as to eliminate any EURO TILE SAND residue left on the tiles. Any EURO TILE SAND residue should go directly into the tiled joints. Wait no longer than 2 to 3 minutes.
(C) • Shower and rinse simultaneously, so as to eliminate any EURO TILE SAND residue. Any residue should go directly into the tiled joints. However, stop showering when you see water retention on the tiled joints. Wait no longer than 2 to 3 minutes. Note: Repeat the directions of STEPS 8a to 8c for all other areas that have not been showered with water.
(D) • Use a leaf blower to remove any excess water remaining on the tiled crevices. This blowing action is necessary to help remove any remaining EURO TILE SAND residue left on tiled surfaces from the previous steps.
IMPORTANT: The water used in steps 8a to 8c will activate a bonding action as well as condensing EURO TILE SAND in the joints. It is important to water the EURO TILE SAND a total of 3 times, as per steps 8a, 8b and 8c. To little water will not properly activate the EURO TILE SAND and will reduce the final performance.
Moss Euro Tile Sand will not cause nor prevent moss, mold or mildew. Moss, mold and mildew are caused by certain on site conditions including excess moisture, shade, absence of ventilation, inadequate cleaning or maintenance, presence of soil or other organic debris left on the product.
1/4” (10 mm) joints 24 x 24 tile with 1/4” joints spacer |
|||
---|---|---|---|
sq. ft. | sq. m. | ||
Slate Grey, Beige, Ivory 35 lbs (15.9 kgs) |
125 sq.ft. | 11.6 sq.m. | |
Black Diamond 35 lbs (15.9 kgs) |
110 sq.ft. | 10.2 sq.m. |
Quantity required depends on the shape and size of the porcelain tiles.
Products | Retail Size | Units per Pallet |
---|---|---|
Euro Tile Sand – Beige | 15.9 kg (35 lbs) | 40 |
Euro Tile Sand – Slate Grey | 15.9 kg (35 lbs) | 40 |
Euro Tile Sand – Ivory | 15.9 kg (35 lbs) | 40 |
Euro Tile Sand – Black Diamond | 15.9 kg (35 lbs) | 40 |
Euro Tile Sand can be stored outside
New waterproof bag, an advanced progressive solution for long-term storage of Euro Polymeric Sand and Dust products. Whether winter, spring, summer, or fall your polymeric sand is protected.
This warranty is given by the manufacturer of this product (hereafter “Manufacturer”). The Manufacturer cannot guarantee results, as it has no control over surface and sub-surface preparation and product application. Moreover, there is no warranty if the tiles are installed directly on bedding sand or concrete foundation. However, for a period of 15 years from purchase, the Manufacturer agrees, if the product is proven to be defective, and on the condition that it was installed pursuant to the method of application of surface and sub-surface preparation described above, to refund the purchase price of the Gator Tile polymeric sand. Proof of purchase is required for any claim.
THE PARTIES AGREE THAT REFUND OF THE PURCHASE PRICE AS STATED IS THE ONLY OBLIGATION OF THE MANUFACTURER. IN ALL EVENTS, THE MANUFACTURER SHALL NOT BE LIABLE FOR ANY OTHER DAMAGES OR COSTS (INCLUDING REMOVAL OR REINSTALLATION OF SAND OR TILES) WHATSOEVER, DIRECT OR CONSEQUENTIAL. TO THE EXTENT PERMITTED BY LAW, THE MANUFACTURER EXCLUDES ANY IMPLIED WARRANTY OF QUALITY, MERCHANTABILITY OR FITNESS FOR PURPOSE. Without limiting the generality of the foregoing, ALLIANCE DESIGNER PRODUCTS INC. shall not be liable for the presence of moss, mold, mildew, or similar factors that may occur on the product after its installation. Please note that this limited warranty applies only when the product is used for residential purposes exclusively (home owners or contractors using the product for single or multi-unit dwellings that are exclusively for residential pedestrian use).
Please note that when the product is used for other pedestrian purposes (mixed-use, commercial, institutional or other), the above terms apply except that the applicable period is reduced to 1 year from purchase.